Laser Beam Accessories & Related Products

CHS-6000 Capacitive Height Sensing System

To attain high quality cutting results, a precise control of the stand-off distance between the nozzle tip and the workpiece is required. The nozzle tip stand-off can be controlled within 0.01mm by using the CHS-6000 Capacitive Height Sensing System.

The CHS-6000 measures the nozzle tip stand-off distance and converts the measurement into an analog output signal. After calibrating the system to three known stand-off distances, the on-board microprocessor digitally linearizes the analog output signal.

Automatic calibration can be accomplished by a simple PMC-interface. Two channel technology allows the user to store two different calibration curves for different nozzle types. For use with conductive work surface. Non-conductive materials require a tactile adapter (TTA-3029-M8-AMX) in place of the capacitive height sensing nozzle.

CHS-6000 Features

• Microprocessor Controlled
• Software Controlled Sensor Calibration
• Linear Range at Standard Calibration: 0.2mm - 5.1mm
• Digital Linearization Linear Range ± 3.5mm
• Maximum Sensing Distance: 50mm
• 3 Point Calibration Teach Process
• ± 10 VDC Analog Output
• 2 Channel Technology for Different Nozzle Designs
• Nozzle Tip Touch Alarm
• Cable Disconnect & Short Alarm
• Quick/Rapid Approach Function
• Reduce Gain Function
• Plasma Detection Function
• Position Hold Function

CHS-6000 Specifications

• Rated Voltage: 110VAC / 220VAC
• Power Consumption: 500ma@110VAC
• Workpiece: Electrically Conductive. Connected to GND
• Analog Output: DC ±10V or 0-10V
• Output Limit: ~±12V
• Aquisition Rate: 2KHz / 500Hz
• Operating Temperature: 0-40 deg C
• Output Impedance: 100 ohm
• Enclosure: Industrial NEMA 12

CHS-6000 Part Numbers:

CHS-6000A: Capacitive Height Sensing System in NEMA 12 Enclosure

CHS-6000-PCB: Capacitive Height Sensing System without Enclosure. Ready for mounting in your equipment.

Ultra-Low Noise Capacitive Sensor Cable Assembly (CHS to JB)

		Part #		Specs
		CHS-6000A-SC15		Triaxial Design 15m length BNC to SMA Connection
		Additional configurations available.

Junction Box

		Part #		Specs
		CHS-6000A-JB		Provides junction between Sensor Cable and Electrode Cable SMA to MCX Connection
		Additional configurations available.

Electrode Cables (JB to NZL)

Haas Part Number	Length (mm)	Connection "A"	Connection "B"
CHS-6000A-EC300	300	MCX	MCX
CHS-6000A-EC300-MCX-SMA	300	MCX	SMA
CHS-6000A-EC300-SMA-SMA	300	SMA	SMA
CHS-6000A-EC450	450	MCX	MCX
CHS-6000A-EC500	500	MCX	MCX
CHS-6000A-EC510	510	MCX	MCX
	Additional configurations available up to 1 meter

Standard Tactile Adapter

		Part #		Specs
		TTA-3029-M8-AMX		For use with non-conductive materials
		Several designs available.

Optional Enclosure

		Part #		Specs
		CHS-6000-encl		Length: 10.5" Width: 7.25" Height: 1.5"
		Several mounting designs available.

Additional options available upon request

We would be happy to discuss a custom designed solution that's right for any project, large or small. For additional information, contact a Haas Laser Technology sales representative today. (973) 598-1150

** Specifications subject to change without notice. Consult a Haas Laser Tech engineer for the latest specification changes or any additional assistance. **